hardware:channels:meters:power:m3303a
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende Überarbeitung | ||
hardware:channels:meters:power:m3303a [2011/12/29 17:05] – [impulsausgang] datenblatt r00t | hardware:channels:meters:power:m3303a [2018/03/25 11:06] (aktuell) – alte Version wiederhergestellt (2018/03/25 10:16) jau | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
- | ===== hantec m3303a | + | ===== Hantec M3303a |
<note warning> | <note warning> | ||
==== ... ==== | ==== ... ==== | ||
Zeile 5: | Zeile 5: | ||
* [[http:// | * [[http:// | ||
* historie zu von ALDI verkauften Stromkostenmessgeräten: | * historie zu von ALDI verkauften Stromkostenmessgeräten: | ||
- | * das GT-PM-04 wurde schon vorher [[http:// | + | * das GT-PM-04 wurde schon vorher [[http:// |
* im Jahr 2009 wurde bei Aldi ein zumindest ausserlich ähnliches Gerät unter der Bezeichnung [[http:// | * im Jahr 2009 wurde bei Aldi ein zumindest ausserlich ähnliches Gerät unter der Bezeichnung [[http:// | ||
* das im Jahr 2008 bei Aldi verkaufte Gerät (GT-PM-02) wurde (zusammen mit dem [[kd_302]]) von der c't getestet, und [[http:// | * das im Jahr 2008 bei Aldi verkaufte Gerät (GT-PM-02) wurde (zusammen mit dem [[kd_302]]) von der c't getestet, und [[http:// | ||
Zeile 43: | Zeile 43: | ||
aus dem datenblatt: | aus dem datenblatt: | ||
- | > 5.4.1 Normal Format | + | > 5.4 Energy Pulse Output |
[...] | [...] | ||
- | > The PulseRateE1, | + | <code> |
- | > quency on output pin E1, when full-scale input signals | + | VIN * VGAIN * IIN * IGAIN * PF * PulseRate |
- | > are applied to the voltage and current channels. The | + | FREQ_E = ------------------------------------------------ |
- | > maximum pulse frequency | + | VREFIN^2 |
- | > is (MCLK/K)/ | + | |
+ | | ||
+ | VIN = rms voltage across VIN+ and VIN- [V] | ||
+ | VGAIN = Voltage channel gain | ||
+ | IIN = rms voltage | ||
+ | IGAIN = Current channel gain | ||
+ | PF = Power Factor | ||
+ | | ||
+ | | ||
+ | </code> | ||
[...] | [...] | ||
- | |||
> 5.4.5 Pulse Output E3 | > 5.4.5 Pulse Output E3 | ||
- | |||
> The pulse output E3 is designed to assist with meter calibration. The pulse-output frequency of E3 is directly | > The pulse output E3 is designed to assist with meter calibration. The pulse-output frequency of E3 is directly | ||
> proportional to the active power calculated from the input signals. E3 pulse frequency is derived using a | > proportional to the active power calculated from the input signals. E3 pulse frequency is derived using a | ||
> simular transfer function as E1, but is set by the value in the | > simular transfer function as E1, but is set by the value in the | ||
> PulseRateE3 Register. | > PulseRateE3 Register. | ||
- | + | > The E3 pin outputs negative and positive energy, but has no energy direction indicator. | |
- | > The E3 pin outputs negative and positive energy, but | + | [...] |
- | > has no energy direction indicator. | + | |
- | + | ||
- | > The pulse width of E3 is configurable. The PulseWidth | + | |
- | > register defines the pulse width of E3 in units of 1/OWR | + | |
- | > or: | + | |
- | < | + | |
- | PulseWidth | + | |
- | t_pw = -------------------------------------------- | + | |
- | - | + | |
- | MCLK / K / 1024 | + | |
- | </ | + | |
- | > The default value is 0. | + | |
> 6.12 PulseRateE3 Register | > 6.12 PulseRateE3 Register | ||
- | |||
> Default = 0xFA0000 = 32000.00 Hz | > Default = 0xFA0000 = 32000.00 Hz | ||
- | |||
> PulseRateE3 sets the frequency of the E3 pulses. The register' | > PulseRateE3 sets the frequency of the E3 pulses. The register' | ||
> is represented in unsigned notation, with the binary point to the right of bit #5. | > is represented in unsigned notation, with the binary point to the right of bit #5. | ||
Zeile 88: | Zeile 80: | ||
< | < | ||
ca. 800w, impulsabstand ca. 200us (0.2ms): | ca. 800w, impulsabstand ca. 200us (0.2ms): | ||
- | 1000/.2/800 = 6.25 impulse/ | + | 1000/.2/800 = 6.25 impulse/ |
ca. 20W, impulsabstand ca. 8ms: | ca. 20W, impulsabstand ca. 8ms: | ||
- | 1000/8/20 = 6.25 impulse/ | + | 1000/8/20 = 6.25 impulse/ |
=> auf jeden fall schonmal sinnvoll/ | => auf jeden fall schonmal sinnvoll/ | ||
- | 6.25 impulse/ | + | 6.25 impulse/ |
6.25000 * 1000 * 60 * 60 = 22500000.00000 | 6.25000 * 1000 * 60 * 60 = 22500000.00000 | ||
ca. 22,5 millionen impusen pro kWh | ca. 22,5 millionen impusen pro kWh | ||
</ | </ | ||
- | der reale wert ist vermutlich 25,6 mio imp/kWh (zweierpotenz). | + | <del>der reale wert ist vermutlich 25,6 mio imp/kWh (zweierpotenz).</ |
eine genauere messung ist noetig um dies zu bestaetigen. | eine genauere messung ist noetig um dies zu bestaetigen. | ||
- | (MCLK ist 4,096 MHz, die bedeutung des pulse-rate registers erschliesst sich nicht so intuitiv aus der erklaerung im datenblatt. (was ist hier "full scale"? | ||
==== belegung CON1 ==== | ==== belegung CON1 ==== | ||
pin1 (rote leitung) beim netzteil, pin12 beim batterie-anschluss: | pin1 (rote leitung) beim netzteil, pin12 beim batterie-anschluss: |
hardware/channels/meters/power/m3303a.1325174755.txt.gz · Zuletzt geändert: 2011/12/29 17:05 von r00t